Proceedings of the Annual Convention of the American Railway Engineering and Maintenance-of-Way Association, Volume 22The Association, 1921 List of members in v. 1- |
Contents
| 165 | |
| 197 | |
| 235 | |
| 243 | |
| 256 | |
| 267 | |
| 315 | |
| 375 | |
| 405 | |
| 412 | |
| 419 | |
| 427 | |
| 434 | |
| 443 | |
| 471 | |
| 481 | |
| 543 | |
| 550 | |
| 565 | |
| 585 | |
| 901 | |
| 925 | |
| 943 | |
| 949 | |
| 956 | |
| 967 | |
| 973 | |
| 978 | |
| 990 | |
| 1003 | |
| 1019 | |
| 1039 | |
| 1045 | |
| 1051 | |
| 1057 | |
| 1076 | |
| 1082 | |
| 1091 | |
Other editions - View all
Common terms and phrases
American Railway Association Appendix Association Automatic Train Control average ballast Board of Direction bolts bracing bridges cables cars cement cent Chairman Chicago cinders circuits Committee recommends Company concrete conductor construction cost creosote cubic foot curve decay defects diameter ductility electric electric locomotives Electrolysis failures feet finished frogs gage grade crossings grade separation highway holes inches inspection installed insulation joints Kans knots length less load Location locomotives manganese Manual manufacture material maximum mechanical methods miles miles per hour necessary Okla operation piece pipe placed plans plates posts practice rail railroad repairs road samples Section side signal specifications speed spikes splicing chamber standard steel stress Sub-Committee submitted surface switch TABLE tamping telegraph Tensile Strength terminals thickness timber tion tons track traffic volts width wire wood wrought iron yard zinc chloride
Popular passages
Page 799 - When a train stops or is delayed, under circumstances in which it may be overtaken by another train, the flagman must go back immediately with stop signals a sufficient distance to insure full protection.
Page 293 - The Commission shall have the exclusive power to determine and prescribe the manner, including the particular point of crossing and the terms of installation, operation, maintenance, use, and protection of each crossing of one railroad by another railroad or street railroad, and of a street railroad by a railroad, and of each crossing of a public road or highway by a railroad...
Page 680 - The manufacturer shall afford the inspector, without charge, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests (except check analysis) and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Page 247 - The provisions of this agreement shall Inure to the benefit of and be binding upon the successors and assigns of the parties.
Page 648 - Structural steel shall conform to the Standard Specifications of the American Society for Testing Materials for Structural Steel for Buildings, Serial Designation A 9-21, as amended to date.
Page 648 - Rivets shall be made of steel manufactured in accordance with the standard specifications of the American Society for Testing Materials for rivet steel for ship or structural work.
Page 680 - This analysis shall be made from a test ingot taken during the pouring of the melt. The chemical composition thus determined shall be reported to the purchaser or his representative, and shall conform to the requirements...
Page 291 - ... to require where, in its judgment, it would be practicable, a separation of grades at any such crossing heretofore or hereafter established and to prescribe the terms upon which such separation shall be made and the proportions in which the expense of the alteration or abolition of such crossings or the separation of such grades shall be divided between the railroad or street railroad corporations affected or between such corporations and the state, county, municipality or other public authority,...
Page 855 - Concrete shall be handled from the mixer to the place of final deposit as rapidly as practicable by methods which shall prevent the separation or loss of the ingredients.